DIN EN 853 1SN is a single-wire-braid hydraulic hose type for conveying hydraulic fluids in equipment and machinery. Its construction generally consists of an oil-resistant synthetic-rubber tube, one high-tensile steel-wire braid, and a weather- and oil-resistant rubber cover. The right hose depends on more than its 1SN designation: buyers should confirm the required inside diameter, working pressure, temperature range, fluid compatibility, routing, and end connections against the supplier’s product data sheet before ordering.
If you are looking for more details, kindly visit our website.
This guide explains the construction and typical uses of 1SN hose, then provides a practical selection framework for B2B purchasing. At Hengshui Xinchi Hose Manufacturing Co., Ltd., we use these details to help buyers compare requirements and request a suitable product specification. Exact ratings can vary by size and product design, so a standard designation alone should not be treated as a complete operating specification.
This guide is intended for hydraulic equipment manufacturers, distributors, maintenance teams, and industrial procurement professionals evaluating hose for a new system or replacement. It is especially useful when a drawing, bill of materials, or existing hose identifies DIN EN 853 1SN but does not provide enough information to complete a purchase. It is not a substitute for equipment instructions, a system risk assessment, or the manufacturer’s technical data.
DIN EN 853 describes requirements for certain rubber hoses and hose assemblies used in hydraulic applications. Within that designation, 1SN refers to a hose construction reinforced by one braid of steel wire. The rubber tube is selected for compatibility with specified hydraulic fluids, while the outer cover protects the reinforcement from the surrounding environment and normal handling.
A typical 1SN hose has three main layers: an inner tube, a steel-wire braid, and an outer cover. The tube and cover are commonly made from synthetic rubber compounds, but the exact compound formulation is product-specific. Buyers should confirm compatibility with the actual fluid, additives, operating temperature, and external exposures rather than assuming that all hoses carrying the same designation behave identically.
The single wire braid provides reinforcement for pressure service, but the hose must be selected as part of a complete assembly. Fittings, crimp specifications, installation quality, and routing all affect safe operation. A hose that meets a nominal construction description may still be unsuitable if its size, pressure rating, or fluid compatibility does not match the system.
| Specification | What to check |
|---|---|
| Hose type | Confirm the requested DIN EN 853 1SN designation and the applicable product documentation. |
| Inside diameter | Match the system connection and required flow; verify the selected size on the technical data sheet. |
| Working pressure | Use the rated pressure for the exact hose size, and consider pressure peaks as well as normal operation. |
| Temperature | Check both fluid and ambient operating conditions against the supplier’s declared range. |
| Bend radius | Check the minimum radius for the selected size and avoid bending the hose more tightly during installation. |
| Assembly details | Confirm fitting type, connection size, hose length, and assembly or crimping requirements. |
Many product specifications for this hose category give a hydraulic-fluid operating range of approximately -40 °C to +100 °C, but the applicable limits must be confirmed for the specific hose and fluid. The declared working pressure varies with nominal diameter, so buyers should not apply one pressure figure to every size. Where the relevant product standard or supplier documentation specifies a burst-to-working-pressure relationship, check that requirement in the current documentation rather than inferring it from the hose name.
1SN hoses are used in hydraulic circuits where a single-wire-braid construction is specified and the selected product’s ratings suit the operating conditions. Potential applications include industrial machinery, mobile equipment, agricultural machinery, and general hydraulic systems. Suitability depends on the actual pressure, fluid, temperature, movement, and installation environment; an application category alone does not confirm that a particular hose is appropriate.
Start with the equipment manufacturer’s specification or the existing assembly markings. Record the hose inside diameter, end connections, length, working pressure, fluid type, and operating temperature. If the hose is being replaced, also inspect the routing and failure location, since abrasion, excessive bending, heat, or unsuitable fittings may have contributed to premature wear.
Link to Hengshui Xinchi Hose Manufacturing Co., Ltd.
Consider dynamic movement as well as static routing. A hose that fits while equipment is stationary may be stretched, twisted, or compressed during operation. Allow for movement, keep the assembly clear of sharp edges and heat sources where practical, and follow the equipment or hose manufacturer’s installation guidance.
A frequent mistake is choosing by outside appearance or nominal diameter alone. Similar-looking hoses may have different constructions, ratings, or fluid compatibility, and an incorrect inside diameter can affect system performance. Buyers should also avoid assuming that a hose’s maximum stated working pressure applies at every size or under every temperature condition.
Another avoidable issue is specifying the hose but not the fittings or assembly requirements. Incorrect end connections, unsuitable crimping, or an assembly that is too short can create installation problems even when the hose itself is correctly selected. Provide a drawing, sample, or complete fitting description where possible, and resolve any mismatch before production or shipment.
Pricing for DIN EN 853 1SN hose is influenced by factors such as hose size, order quantity, requested length, fittings, packaging, and documentation requirements. Minimum order quantities and lead times depend on the specific product and order conditions; they should be confirmed in a current quotation rather than assumed from a general catalogue description. For a meaningful comparison, ask suppliers to quote against the same specification and delivery terms.
If you are sourcing for repeat production, share your expected order pattern and packaging preferences when requesting a quotation. This allows suppliers to discuss practical ordering options without treating an unconfirmed forecast as a commitment. For project orders, confirm the required delivery date, inspection documents, and any approval steps before placing the purchase order.
Evaluate suppliers on their ability to respond clearly to the technical specification, not on the product name alone. Request a current data sheet for the relevant size, declared operating limits, and clear identification of the proposed hose and fittings. Check that the quotation states quantity, length, connection details, packaging, delivery terms, and any documents included.
At Hengshui Xinchi Hose Manufacturing Co., Ltd., we can review a buyer’s application details and discuss DIN EN 853 1SN hose requirements for product evaluation and sourcing. To support an accurate response, provide the size, fluid, operating pressure and temperature, required length, fitting details, quantity, and destination. Where a requirement is uncertain, we recommend confirming it with the equipment designer or responsible engineer before purchase.
DIN EN 853 1SN identifies a hydraulic hose construction with one steel-wire braid, but the designation alone does not establish whether a particular hose will suit your system. The right selection requires size-specific pressure and bend-radius data, verified fluid and temperature compatibility, and correctly specified fittings and installation conditions. Begin with the equipment requirements, then compare them with the supplier’s current technical documentation.
For your next step, prepare the application details and request a quotation for the exact hose size and assembly configuration. Hengshui Xinchi Hose Manufacturing Co., Ltd. can help review those requirements and discuss suitable sourcing options. A complete specification makes it easier to evaluate the product, compare suppliers, and reduce avoidable purchasing or installation mismatches.
The company is the world’s best DIN EN853 1SN Hydraulic Hoses supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.