2SN vs 2SC Hydraulic Hose: Bend Radius, Outer Diameter, and Pressure

11, Nov. 2026

 

2SN vs 2SC Hydraulic Hose: Bend Radius, Outer Diameter, and Pressure

For a given nominal bore, EN 857 2SC hose is generally more compact and can bend through a tighter radius than EN 853 2SN hose. Their pressure ratings may be similar in some sizes, but they are not interchangeable by default: working pressure, outer diameter, and minimum bend radius depend on the hose size and the manufacturer’s specifications. For example, representative product tables commonly list a 6 mm bore hose at up to 400 bar, with a minimum bend radius around 100 mm for 2SN and 75 mm for 2SC. Treat these figures as size-specific examples, not a substitute for the exact product datasheet.

For more information, please visit our website.

Key Takeaways

  • Both hose types use two steel-wire braid reinforcement layers, but 2SC has a compact construction designed for tighter routing.
  • 2SC often has a smaller outer diameter and shorter minimum bend radius than 2SN of the same nominal bore; confirm both dimensions for the exact product.
  • Do not assume one type always has a higher pressure rating. Compare the stated working pressure at the required bore and temperature.
  • Choose against the equipment specification, fitting compatibility, routing space, and operating conditions—not the hose label alone.

What the 2SN and 2SC Designations Mean

EN 853 2SN and EN 857 2SC are wire-braided hydraulic hose types. Both use two steel-wire braid layers to reinforce a rubber hose assembly, but their construction and dimensional requirements differ. In general, 2SC is a compact hose intended to help with installations where space is restricted or hose routing requires tighter bends.

The designation does not describe every performance detail of a finished assembly. Actual dimensions, pressure ratings, temperature limits, cover options, and fitting compatibility should be checked on the supplier’s datasheet. The hose assembly—including its end fittings and installation—must also be suitable for the equipment and service conditions.

2SN vs 2SC: Specification Comparison

Comparison point EN 853 2SN EN 857 2SC
Reinforcement Two steel-wire braid layers Two steel-wire braid layers in a compact construction
Outer diameter Often larger for the same nominal bore Often smaller for the same nominal bore
Bend radius Generally requires a wider bend Generally supports a tighter bend
Pressure Depends on bore and product specification Depends on bore and product specification; do not assume it is higher or lower in every size
Typical selection priority Applications where the specified 2SN construction and dimensions fit Installations where compact routing and space savings are important

Bend Radius: Where 2SC Can Help

Minimum bend radius is the smallest radius at which a hose can be bent without exceeding the manufacturer’s permitted limit. A smaller permitted radius can make it easier to route a hose through a compact machine or around nearby components. In representative product tables for a 6 mm nominal bore, a minimum radius may be listed as approximately 100 mm for 2SN and 75 mm for 2SC.

Those figures are examples, not universal values for every brand or product range. The minimum radius usually changes with nominal bore, so compare like-for-like sizes using the same supplier’s documentation where possible. Also distinguish the hose’s minimum bend radius from the space needed for fittings, clamps, movement, and service access.

Outer Diameter: Check the Installed Envelope

2SC is commonly selected when a compact outside profile is useful, and its outer diameter is often smaller than that of 2SN at the same nominal bore. This can help when a hose must pass through a limited opening or share a route with other components. However, there is no single outer-diameter value that applies to every 2SN or 2SC hose size.

Request the actual outside diameter for the exact hose construction and size, and measure the available clearance in the equipment. Remember that the assembled envelope can be larger than the hose body because of the fitting, protective sleeve, bend, or clamp. If an existing hose is being replaced, record its bore, outside diameter, length, fitting details, and routing before ordering.

Pressure: Compare Working Ratings by Bore

Pressure capacity is size-specific. As one representative reference point, product tables may list a 6 mm bore 2SN or 2SC hose with a working pressure of up to 400 bar, but other sizes can have different ratings. This example does not mean the two hose types have identical pressure ratings throughout their size ranges.

Use the manufacturer’s stated working pressure, not the burst pressure, as the basis for selecting a hose for normal operation. Confirm that the rating applies at the required temperature and fluid conditions, and account for pressure peaks or pulsation where the equipment manufacturer requires it. Never select a lower-rated hose solely because its outside diameter or bend radius better fits the installation.

Hengshui Xinchi Hose Manufacturing Co., Ltd. are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

Which Hose Fits Your Application?

Choose 2SC When Space and Routing Are the Priority

2SC is a practical candidate when the installation is crowded, the route includes tighter turns, or a smaller hose outside diameter is needed. It can reduce routing difficulty when its published bend radius and dimensions meet the equipment requirements. Check that the required pressure rating, fittings, and operating conditions also match before specifying it.

Choose 2SN When the Equipment Specifies It

2SN may be the right choice when the machine documentation, replacement specification, or existing assembly calls for EN 853 2SN. It can also suit a route with enough clearance for its dimensions and bend requirements. Do not replace a specified hose type with 2SC merely because it appears more compact; confirm suitability with the equipment manufacturer or a qualified hose specialist.

A Practical Buyer Selection Checklist

  1. Confirm nominal bore. Match the required internal diameter to the system specification and flow needs.
  2. Check pressure and temperature. Compare the published working pressure and operating limits with the equipment conditions.
  3. Measure the route. Check minimum bend radius, outside diameter, available clearance, and movement during operation.
  4. Verify the assembly. Specify fitting type, connection size, orientation, hose length, and any protection required.
  5. Confirm replacement approval. If changing from 2SN to 2SC or vice versa, obtain acceptance from the equipment maker or responsible engineer.

Common Selection Mistakes

A frequent mistake is treating 2SN and 2SC as identical because both use two wire braids. The construction designation alone does not confirm equal dimensions, pressure ratings, or assembly compatibility. Another mistake is checking bend radius without considering the real installation, including movement, fitting clearance, and the possibility of rubbing against adjacent parts.

Buyers should also avoid comparing burst pressure with working pressure, or using a rating from one bore to approve another. If a datasheet does not clearly show the required value, ask the supplier to confirm it in writing for the exact size and construction. This simple verification can prevent specification mismatches during procurement and installation.

How Hengshui Xinchi Hose Manufacturing Co., Ltd. Can Support Your Inquiry

At Hengshui Xinchi Hose Manufacturing Co., Ltd., we support B2B buyers by reviewing the application details needed to identify a suitable hydraulic hose specification. Share the required standard, nominal bore, working pressure, operating temperature, hose length, fitting details, and routing constraints. We can then confirm the available product information and discuss a quotation based on the requested configuration.

For a replacement or new project, send the existing hose marking or technical drawing when available. We recommend confirming the exact outer diameter and minimum bend radius against the selected product datasheet before finalizing the order. This gives both the buyer and supplier a clearer basis for checking fit and specification.

Final Recommendation

For comparable nominal bores, 2SC is generally the more compact option, with a tighter minimum bend radius and often a smaller outside diameter. 2SN remains appropriate when it is specified by the equipment manufacturer or when its dimensions and performance meet the application requirements. Neither designation should be selected on bend radius or pressure alone.

Before purchasing, compare the exact hose datasheets for bore, working pressure, outside diameter, minimum bend radius, temperature limits, and fitting compatibility. If you are deciding between 2SN and 2SC for a new system or replacement assembly, send your operating requirements to Hengshui Xinchi Hose Manufacturing Co., Ltd. for a specification review and sourcing discussion.

The company is the world’s best 2SN vs 2SC Hydraulic Hose: Bend Radius, Outer Diameter, and Pressure supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.